Avoid Future Headaches: Don't Contaminate Your Stainless Steel

Avoid Future Headaches: Don't Contaminate Your Stainless Steel

Avoid Future Headaches: Don't Contaminate Your Stainless Steel

Last Updated: 11/11/21 at 1:29pm

Author: Les Boulton

The contamination of stainless steel occurs when the stainless comes into contact with an iron object, for example a tool, and as a result the iron particles are ‘smeared’ onto the stainless. When put in a corrosive environment (think most cities on the coast) these iron particles rust, leaving a very unsightly brown rust. The contamination often isn’t apparent until after the installers have left the site but sooner or later, the invisible iron particles will probably rust. This doesn’t look good, and can not only harm the reputation of the installer, but require them to return to the site to remedy the problem.  To help you avoid this headache, we would like to share some tips gleamed from our 20 years of experience:

 

Avoid Contamination from Tools

  • Drive/Screw Tips should be chrome vanadium steel. Chrome vanadium protects the iron in the tool from coming into contact with the fastener;
  • Allen keys and security screw tools should be hardened chrome plated.
  • Cuttings discs should be made from aluminium oxide, be ‘iron’ or ‘carbon – steel’ free, or be labelled ‘for stainless steel’.
  • Hammers should be good quality hardened-chrome plated steel or stainless steel.
  • All tools for stainless steel should be kept separate from others and be used exclusively for stainless steel.

Consider Iron Particles in the Environment

  • Keep stainless steel products protected from iron in the environment. A classic example is iron filings from grinding and cutting carbon steel on site flying around and ending up all over the stainless. Sooner or later they will be leaving rust marks. So cover the stainless in plastic sheet/wrap until the job is completed.
  • This applies to the workshop too – physically separate (preferably with a wall) ‘carbon-steel’ fabrication from stainless steel fabrication.
  • Maintain a clean working environment where possible ensuring that immediate working areas are free of any metals filings or particles of aggregate.
  • Protect stainless steel from general workshop grime, weld spatter and grinding sparks.
  • Avoid walking on stainless steel products with footwear that can damage or impregnate the surface of the material with corrosive particles.

Handle Stainless Correctly

  • Don’t use steel straps for packaging. Instead use plastic or plastic covered straps and/or ropes for retaining or lifting stainless steel. It is important to ensure that ropes or straps are themselves free from iron contamination, for example they may have been used to tie steel. Ideally have straps just for use on stainless.
  • Don’t use solvents containing chlorine.
  • Use marking inks with low chloride content.

 Next month we will be discussing how to clean surface contamination.

For more information on how best to avoid contamination of stainless. Visit the following links:

 

NB: This information is provided as a guide only and Anzor does not accept liability for the application of this information. For advice about stainless steel contact the NZ Nickel Institute


About Les Boulton

Les Boulton is a former and retired New Zealand Consultant to the Nickel Institute and Branch President of the NZ Branch of the Australian Corrosion Association Inc and NZ Stainless Steel Development Association. With a BSc and MSc (Hons) majoring in Chemistry, Metallurgy and Corrosion Science from the University of Auckland, Les has obtained over 40 years experience in materials engineering and corrosion consultancy. He is the Principal Consultant of Les Boulton & Associates Ltd, materials and corrosion consultants in Auckland. He has been a Consultant to the International Nickel Institute in Brussels, Belgium for 20 years.

Les has been a member of the ACA (Auckland Corrosion Association Inc) for 47 years and is an ACA Life Member. He is a past ACA Australian President, President of the ACA NZ branch and now serves on the ACA Auckland Division Committee and NZ Branch Committee. A notable article that Les has written is the Corrosion of Building Assets - Problems and Prevention. Check out Les on his LinkedIn profile for more information.

Learn Something New

To receive useful info and product updates add your details below

Anzor Wallchart

Wall Chart

Request a copy of our Engineering & Marine, or Construction Wall Chart.

Anzor Catalogues

Standard Catalogues

Click here to download a PDF of our Engineering Catalogue. This catalogue includes stainless fasteners and fittings, marine hardware and construction brackets.

Anzor Catalogues

Construction Catalogues

Click here dot download a PDF of our Construction Catalogue. This catalogue includes stainless/galvanized fasteners and fittings, and construction brackets.

You are subscribed to push notifications but they are not enabled in your browser.
Please either enable push notifications here or unsubscribe here.